Contents

Articles

2024
2023
2022
2020
2019
2018
2017
2016
2015
2014
2013
2012
2011
2010
2009

Change log

Share this page

Deploying MobileIron 9.1+ on KVM

Introduction

#

Recently MobileIron announced the release of Core and Connector version 9.1.0.0 and with it comes the newly-supported option for KVM deployments.

This is good news for enterprises who rely on Linux (well, Ubuntu Linux officially but all the same) as it’s now possible to install both the Core and Enterprise connector without the need for VMWare, Hyper-V or physical hardware.

MobileIron Sentry support

#

To date there has been no update for the MobileIron Sentry. Due to this, the following guide will not be relevant and any installations will not be supported by MobileIron

Prerequisites

#

Before continuing, please ensure you meet the following prerequisites:

MobileIron

#

Core version: 9.1.0.0
Connector version: 9.1.0.0

Linux host

#

Flavour: Ubuntu Server
Server version: 14.04 or above
QEMU version: 2.0.0 or above

This guide assumes a fresh copy of Ubuntu server 14.04.4 or newer has been installed, but not yet modified. Copies of Ubuntu server can be obtained on the Ubuntu website. The server should be accessible either directly or via SSH. It also goes without saying the MobileIron ISO has been downloaded and is readily available for installation. To get a copy of the MobileIron software please speak to your MobileIron account manager.

#

MobileIron recommend using Virtual Machine Manager (virt-manager) version 0.9.5 or above and installation via GUI. However, this guide will also include steps for installation via commandline and remote Virtual Machine Viewer (virt-viewer) on Windows (referred to as “Remote Viewer”).

Installation

#

Ubuntu server QEMU packages

#

From the command line, install QEMU KVM, virt-install and bridge utilities:

sudo apt-get install qemu-kvm qemu virtinst bridge-utils

Setup the network bridge

#

A network bridge will allow the VM to look and behave as if it’s sitting directly on the LAN. This avoids issues with port forwarding from host to guest. This step is optional, but recommended.

sudo vim /etc/network/interfaces

Edit the file by first typing i. This will display INSERT in the lower left corner and allows editing of the document.

A typical interfaces file will look as follows:

# The primary network interface

auto ens33
iface ens33 inet dhcp

In order to create the bridge, the primary interface (referred to above as ens33) will need to be set to manual and the new bridge interface br0 setup below:

# The primary network interface

auto ens33
iface ens33 inet manual

auto br0
iface br0 inet static
    address 192.168.0.150
    netmask 255.255.255.0
    network 192.168.0.0
    broadcast 192.168.0.255
    gateway 192.168.0.1
    dns-nameservers 192.168.0.1
    dns-search localdomain
    bridge_ports ens33

In the above example, the bridged interface br0 has been assigned a static network IP based on the LAN in which it sits. Netmask, network and broadcast must reflect the properties of the LAN network, while gateway and the DNS server(s) should echo those that are already present in the network.

DNS search is optional, but provides the server a simple way to search for other servers in the same domain on the LAN.

Most importantly, bridge_ports is set to ens33 – the physical NIC of the server.

When complete, tap the Escape key, :wq and exit with Enter.

At this point, either reboot the server or restart the networking service to enforce the changes made to the network configuration:

sudo reboot

Install MI connector via VMM

#

From a remote *nix machine running virt-manager, ensure key-based authentication is set up first to avoid connection errors (that is to say, you can ssh user@ip without needing to input the password from a terminal) then connect to the KVM server by clicking File > Add Connection and inputting the relevant user and hostname (as well as checking the checkbox for Connect to remote host).

image-1

As an example, if the SSH user with key-based authentication is jason and the host is 10.10.10.98, these make up the username and hostname respectively.

Click Connect when done.

To create a new virtual machine, right click on the remote host and click New

image-2

Follow the prompts through 1 to 5 using the following screenshots as a guide:

image-3

image-4

image-5

image-6

image-7
Recall the bridge created earlier – this can be now selected under Network selection

Click Finish to create the virtual machine.

The MobileIron installation can now continue as normal by typing vm-install at the prompt in the newly-opened console window.

image-8

Install MI connector via CLI

#

Following the reboot of the KVM host, log back in.

Time limit!

#

Before running the following command, ensure you have the Remote Viewer application installed on your remote machine. You will have 30 seconds to open the remote viewer and input the vm-install command on the MobileIron installer before the system will fail to boot, and the VM configuration file will need to be manually edited to re-add the MobileIron ISO file.

First ensure the MobileIron ISO has been downloaded to the KVM host. If it has been downloaded to a remote *nix workstation, you can use SCP to copy it over using SSH, for example on your workstation:

scp /home/user/mobileiron-9.1.0.0-64.iso user@10.10.10.98:/home/user/

If SCP isn’t an option, FileZilla or another SFTP application may also be used.

To create a new VM from the command line, enter the following command; the bold entries need to be customised in order to match the environment:

sudo virt-install --name=mobileiron-connector --os-type=linux --network bridge=br0 --vcpus=4 --disk path=/home/user/mobileiron-connector.qcow2,size=20 --cdrom=/home/user/connector-mobileiron-9.1.0.0-64.iso --boot=cdrom,hd --graphics spice,listen=0.0.0.0 --ram=7629 --serial file,path=/home/user/serial

Where:

  • name is the name of the virtual machine
  • os-type is the type of operating system, like Linux or Windows
  • network is the network interface to use
  • vcpus is the number of virtual connectors to provide the virtual machine
  • disk is the virtual disk path and size which will be created if it doesn’t exist
  • cdrom is the path to the bootable ISO
  • boot is the boot order
  • graphics provides the console for the Remote Viewer application
  • ram is the amount of RAM to assign to the virtual machine
  • serial is an optional serial file to pipe the MobileIron serial console

On pressing Enter virt-install will begin the installation of the virtual machine, and stop on Domain installation still in progress. Waiting for installation to complete.

Immediately following this message, a 30 second timer starts on the MobileIron boot screen.

Open Remote Viewer and input the connection address:

image-9

By default, this will be spice://ip-or-host:5900 for the first virtual machine to boot, with the port incrementing by 1 for every virtual machine running. The port can optionally be set manually by editing VM configuration file.

On clicking connect, the Remote Viewer will load the remote console where installation can be continued as normal. If the session disconnects, simply re-open it again.

image-10

edit_note Edit this page.

Articles

2024
2023
2022
2020
2019
2018
2017
2016
2015
2014
2013
2012
2011
2010
2009